Is your Razor E-series scooter acting up? You’re not alone. That little reset button (or circuit breaker) can be the root of many headaches. Many riders find their Razor E-series reset button not working when they need it most.
I’ve spent countless hours working with every model in the E-series lineup – from the E90 to the E300, including all those fancy Glow versions. Trust me, they all work pretty much the same way under the hood.
This guide tackles the most common reset button problems head-on:
- When pushing the button does absolutely nothing
- When that stubborn button gets stuck
- When pressing it just isn’t fixing your scooter
I’ll show you exactly how to replace a faulty button, check all the critical connections, and share some insider tricks that most manuals don’t mention. And if all else fails, I’ve got some alternative reset methods that might just save your ride.
Let’s get your scooter back on the road.
Why Razor E-Series Reset Button Not Working?
Button Not Responding
The Problem: You press the reset button and… nothing happens.
Fix It:
- Make sure your scooter is turned on with a charged battery. Dead batteries often masquerade as button problems.
- Take a close look at the button area. Dirt and gunk love to collect here and block proper contact. A gentle cleaning might do the trick.
- Pop the deck open and check the wires connected to your reset button. Loose connections are silent troublemakers.
- If all else fails, swap in a new reset button unit.
Stuck or Jammed Button
The Problem: The button is physically stuck and won’t press down or pop back up properly.
Fix It:
- Look for anything that might be jamming the mechanism. Even tiny debris can cause big problems.
- Got a damaged button? Time for a replacement.
- Try a tiny drop of electrical-safe lubricant to free up that stubborn button.
Reset Not Effective
The Problem: You press the button, it clicks, but your scooter still has the same issue.
Fix It:
- Double-check your manual for the exact reset procedure. Timing matters with these buttons.
- Open up the deck and verify all connections between the controller and reset button are solid.
- If the button seems mechanically fine but doesn’t work, replace it with a new unit.
- Also Read: How to Charge Razor Scooter Without Charger
How to Check if the Reset Button Works
You can easily test your reset button with a multimeter.
Remove the Deck Board: First, unscrew the deck to reach the reset button from inside. You’ll see two pins on the button.
Test the Pins for Continuity: Touch the multimeter probes to the two pins on the reset button.
Listen for a Beep: If the multimeter beeps when you press the reset button, it means the button is working. If there’s no beep, the reset button is faulty and should be replaced. This quick test helps you know right away if your reset button is in good shape or needs a swap.
How to Replace the Reset Button on a Razor E-Series Scooter
If you need to replace the reset button on your Razor E-series scooter, here’s a simple guide. The reset button is located on the side of the foot deck, next to the On/Off switch, and is connected to the battery compartment inside the scooter.
This process works for most Razor E90, E1XX, E200, and E300 models, including Core and Glow versions, since they use the same style of reset button.
What You’ll Need
- Screwdriver
- Replacement reset button (make sure it’s compatible with your Razor model; a 20-A fuse is usually a safe bet)
Step-by-Step Instructions
Stay Safe: Turn off your scooter and disconnect the battery before you start.
Open the Deck: Use a screwdriver to remove the six screws on the deck so you can access the inside.
Find the Reset Button: Look for the reset button inside the battery compartment.
Remove the Battery Bar: Unscrew the two screws holding the battery bar, then lift the batteries out of the way.
Disconnect the Wires: Gently unplug the red and black wires from the reset button.
Remove the Old Button: Unscrew the reset button from the outside of the deck and take it out.
Install the New Button: Put the new reset button in place and screw it in securely.
Reconnect the Wires: Attach the red and black wires to the new button, making sure they’re firmly connected.
Put Everything Back: Place the batteries back in and secure the battery bar with its screws.
Close the Deck: Screw the deck back on with the six screws you removed earlier.
Test the Button: Reconnect the battery, turn on the scooter, and press the reset button. If the power switch lights up, you’re good to go.
With these steps, you can easily replace the reset button and get your Razor scooter working safely again. Replacement buttons are easy to find online, so getting the right part shouldn’t be a problem.
- Also Read: Gotrax GXL V2 Throttle Not Working
How to Inspect Connections Related to the Reset Button
Make sure all the connections around the reset button are secure and working properly by following these steps:
Check Signal Flow: Before replacing the reset button, open the battery compartment. You’ll see red and black wires connected to the reset button. Look for any loose or damaged wires and connectors.
Inspect Wiring Between Controller and Reset Button: The controller sits next to the batteries, close to the reset button. Make sure all wires between the controller and reset button are firmly connected. Fix or replace any loose or damaged wires.
Test Wire Continuity: Use a multimeter set to continuity or resistance mode. Touch the probes to each wire’s ends. A beep or low resistance means the wire is good.
Check Battery Connections: Confirm the battery is supplying a steady 24V. Also, check that the battery connections are tight and free of corrosion. If you see corrosion, clean it with vinegar.
Reassemble and Test: Once everything looks good, put the scooter back together and test the reset button to make sure it works properly.
Additional Troubleshooting Tips for Your Razor E-Series
Check the Battery: Make sure your Razor E-series battery is fully charged. A weak or dead battery can cause problems, including issues with the reset button. Charge it completely, then try again.
Use the User Manual: Look at the user manual that came with your scooter. It has clear instructions on how to use the reset button and fix common problems.
Contact Razor Support: If your scooter still isn’t working right and it’s under warranty, contact Razor customer support. They can help you with expert advice or repairs.
Replace Faulty Parts: If the reset button is broken, you can order a replacement or get it fixed by a professional. Just be sure to get the right part for your model.
Try Other Solutions: Sometimes you don’t need the reset button to fix an issue. Check the manual or search online for other ways to solve your problem.
- Also Read: Hiboy S2 Scooter Won’t Turn On
Alternative Ways to Reset Your Razor Scooter
If the reset button isn’t working or you want to try something else, these simple methods might help fix minor issues.
Disconnect and Reconnect the Battery
- Turn off your scooter completely.
- Find the battery compartment, usually under the deck.
- Unplug the battery connector.
- Wait a few minutes, then plug it back in.
- Turn the scooter on and see if it’s working properly.
Power Cycle Using the Power Switch
- If your scooter has a separate power switch, turn it off.
- Wait for 1-2 minutes to let any leftover power drain.
- Turn the power switch back on.
- Check if the problem is fixed.
Look for a Manual Reset Method
- Check your Razor E100 user manual for any special reset steps.
- Some scooters let you reset using a combination of the throttle, brake lever, and start button.
- There might also be specific button sequences to try as an alternative reset.
- Also Read: Gotrax GXL V2 Not Accelerating
Conclusion
Fixing reset button issues on Razor E-series scooters (E90, E100, E125, E150, E175, E200, E300) takes a clear, step-by-step approach. From simple troubleshooting to replacing the button, everything you need to know is covered here.
Safety comes first, with easy-to-follow instructions for replacing the reset button. Checking connections, battery health, and trying alternative reset methods will help you solve most problems.
This guide is designed to help you keep your Razor E-series scooter running smoothly and enjoy every ride without hassle.